Structured Network & AV Cabling Boston, MA
Every project at Video Wall Installation Boston MA depends on the cable behind it, so we also design and install Cat6, Cat6A, fiber and low-voltage cabling for offices, campuses and hospitals across the city. From century-old brick in Back Bay to new towers in the Seaport, our crews route, terminate, test and label every run.
Planning a fit-out, move or cleanup? Book a site walk-through.
How we install structured cabling in Boston, MA
Cable is the part of a project nobody sees and everybody depends on. When it is planned well, displays, phones, cameras and wireless access points just work and can be moved or upgraded for years. When it is not, every change means tracing unlabeled wires through a ceiling.
We plan network and AV cabling together, because the two now share the same infrastructure. Video walls, AV-over-IP, conference rooms and digital signage all ride on copper and fiber, so we size each run for the bandwidth, power and distance it will actually carry, not just today’s desk count.
Boston’s older buildings rarely have clean pathways. We survey existing chases, risers and ceiling spaces, pull plenum-rated cable where code requires it, fire-stop every penetration through rated walls and floors, and use paintable surface raceway where plaster walls cannot be opened. In newer towers we work with your general contractor to get pathways in before the ceilings close.
Every run is terminated, tested and labeled to match the patch panels and outlets, and you receive test results and as-built drawings at handover.
Our video wall and AV services in Boston, MA
Most projects don’t stop at the wall itself. Here’s everything else our crews handle across the city and the surrounding towns.
Digital Signage Installation
Wall screens, kiosks and media players for lobbies, campuses and storefronts, with content scheduling set up so your team can update messages without calling us.
Control Room Display Systems
Operator walls for hospitals, utilities, security teams and trading floors, built with redundant inputs and processors to run around the clock.
AV System Integration
Displays, speakers, microphones and touch-panel control tied together, so a single button sets up the whole room.
LED Display Rental & Event Setup
Temporary LED walls for conferences, galas and trade shows at venues across the city, delivered, rigged, run and taken down on your schedule.
Projector & Projection Screen Install
Ceiling-mounted projectors and fixed or motorized screens for lecture halls, auditoriums and training rooms, aligned and focused on site.
Conference Room AV Solutions
Displays, cameras and conferencing gear for huddle rooms and boardrooms, set up to work with Teams, Zoom and Google Meet.
Video Wall Maintenance & Repair
Recalibration, panel and power-supply replacement, and scheduled service for existing walls, including ones another crew put in.
Cabling projects we handle across Boston, MA
From a single conference room to a multi-floor fit-out, these are the jobs that come through our schedule most often:
- Office fit-outs and tenant moves
- Video wall and digital signage cabling
- Conference room and AV-over-IP runs
- Wireless access point and PoE device drops
- Fiber backbones between floors and buildings
- Telecom room and rack builds
- Security camera and access control cabling
- Lab and hospital cabling in occupied spaces
- Campus building and classroom upgrades
- Cable cleanup, re-dressing and abandoned cable removal
- Moves, adds and changes for growing teams
- Testing and documentation of existing cabling
Cabling specifications for Boston, MA projects
Distance, bandwidth and how long you plan to stay in the space decide which cable fits. Here’s how the common options compare.
| Specification | Cat6 | Cat6A | Multimode fiber (OM3/OM4) | Singlemode fiber (OS2) |
|---|---|---|---|---|
| Typical use | Desk drops, phones, displays | Video walls, AV-over-IP, wireless access points | Backbones inside a building | Long backbones and building-to-building links |
| Maximum channel length | 100 m (1 Gb); about 55 m at 10 Gb | 100 m at 10 Gb | About 300–400 m at 10 Gb | Several kilometers and beyond |
| AV suitability | 1080p HDBaseT and basic AV control | 4K HDBaseT and 10 Gb AV-over-IP | Long AV-over-IP and video wall links | Campus-wide AV and broadcast feeds |
| PoE | Standard PoE devices | Better heat handling for high-power PoE | Not applicable | Not applicable |
| Jacket ratings | Riser or plenum as code requires | Riser or plenum as code requires | Riser, plenum or armored | Riser, plenum, armored or outdoor-rated |
| Local site notes | Fine for most desks in short-lease spaces | Best choice for long-term fit-outs | Common between closets in older towers | Needed for campus links between buildings |
Our cabling installation process
Every project follows the same five steps, whether it is ten drops or a whole floor.
-
Site survey
We walk the space, find existing pathways, closets and risers, and note wall types, ceiling access and building rules for after-hours work.
-
Design and quote
You get outlet locations, cable types, pathway routes, rack layout and a labeling scheme, plus a fixed quote before work begins.
-
Pathways and pulls
We install supports, conduit and raceway, pull cable with proper bend radius and separation, and fire-stop every rated penetration.
-
Termination and testing
Every copper and fiber run is terminated on patch panels and outlets, then tested end to end and labeled to match the drawings.
-
Documentation
We hand over test results, as-built drawings and a labeling key, so any future move or upgrade starts with an accurate map.
From pathways to patch panels in Boston, MA
Good cabling is invisible because of the work behind it. These are the four areas every project draws on.
Pathways in old and new buildings
Brick, plaster and timber in older neighborhoods need careful routing through chases and ceilings, while new towers need pathways coordinated before ceilings close. We use the least invasive route that still meets code.
Code and fire safety
We use plenum-rated cable in air-handling spaces where code requires it, keep low-voltage runs separated from power, and fire-stop every penetration through rated walls and floors so your inspections go smoothly.
Network and AV together
AV-over-IP, video walls and conference rooms share the network now. We plan runs, switch ports and PoE budgets with your IT team so AV traffic and office traffic both have the room they need.
Racks and documentation
Neat racks with proper cable management, labeled patch panels and as-built drawings make every future change faster. When it is time to add displays, the same team handles the video wall on top.
Cabling projects across Boston, MA
Offices, campuses, hospitals, labs and venues all need cabling that lasts. These are the kinds of projects we plan for here.
Office fit-outs
Full-floor cabling for new tenants, scheduled around general contractor milestones and finished before move-in day.
Historic buildings
Careful routing through plaster, brick and timber, with surface raceway and existing chases where walls cannot be opened.
Hospitals and clinics
Cabling in occupied clinical spaces, coordinated with facilities teams around infection control and patient areas.
Labs and research facilities
Network, instrument and AV cabling for labs, with clean routing and documentation for fast-changing research layouts.
Universities and colleges
Classroom, residence hall and building-to-building fiber links, often scheduled between semesters or over the summer.
Tech offices and data rooms
High-density Cat6A and fiber for engineering floors, server rooms and network operations spaces.
Cabling questions from Boston, MA businesses
Straight answers to what clients ask us most before a cabling project.
Should we install Cat6 or Cat6A?
Cat6 is fine for most desk connections and many AV runs. Cat6A supports 10-gigabit speeds over the full 100-meter channel and handles high-power PoE and 4K HDBaseT more comfortably, so we usually recommend it for video walls, AV-over-IP, wireless access points and anything you expect to keep for many years.
Can you run new cable in an old Boston building without opening every wall?
Usually. We look for existing chases, risers, abandoned flues and ceiling spaces first, and use paintable surface raceway or floor channels where walls cannot be opened. Where a wall does need to be opened, we keep the access small and coordinate patching with your contractor.
Do you test and document every cable?
Yes. Every copper and fiber run is tested after termination, and you receive the test results, a labeling scheme that matches the patch panels and outlets, and as-built drawings showing where each cable goes.
Can you clean up the messy cabling we already have?
Yes. We trace and label what is in use, remove abandoned cable where code requires it or where you want the space back, re-dress racks and patch panels, and leave you with documentation for what remains.
Can you work after hours in an occupied office?
Yes. Much of our cabling work in managed buildings happens evenings and weekends, with freight elevator bookings and insurance certificates arranged in advance, so your staff and network stay up during business hours.
Contact our Boston, MA cabling team
50 Franklin St, Boston, MA 02110Phone: (978) 783-4632
Email: [email protected]
To get an accurate quote faster, have these ready when you reach out:
- A floor plan, or the number of drops and where they go
- What will connect: desks, displays, video walls, access points or cameras
- Building type and age, plus ceiling and wall construction
- Location of your telecom room or existing racks
- Building rules: after-hours work, freight elevator or insurance requirements
- Your target completion or move-in date
Ready to wire it right the first time? Talk to our crew today.